找回密码
 注册
X系列官方授权正版
搜索
查看: 914|回复: 5

Build a paper plane

[复制链接]
发表于 2007-5-27 08:54:00 | 显示全部楼层 |阅读模式

1. Start with an ordinary sheet of 8 1/2" x 11" - 21.6 x 28 cm (U.S.standard writing paper size). The exact size is not important, it should be rectangular and not square. The paper should be at least 20 Lb. bond or copy paper.

2. Fold over the left hand corner as shown.

3. Crease


4. Result

5. Fold over the right hand corner.

6. Crease


7. Result

8. Carefully close in the sides as shown.

9. Fold down the center line from front to back.


10. Fold the resulting left hand tip up as shown.

11. Crease along the bottom edge.

12. Repeat the same procedure on the right section.

... continued from steps 1 to 12

13. Fold the left hand point back.

14. Crease

15. Mirror the same folds on the right panel.



16. Bend the left panel as shown.

17. Crease from back to front only 2/3 of the way.

18. Study photos 18 and 19 carefully. These folds are difficult to describe. Try to duplicate them as shown in the photos.


19. Mirror the folds on the right.

20. Turn the plane over and fold the point back and crease as shown.

21. Turn the plane over again. The result should be similar to the photo.


22. Crease wing as shown.

23. Moisten the crease with your tongue. Do this slowly and carefully or you could receive a painful paper cut on your tongue.

24. Carefully tear off strip of paper. Save the strip of paper because you are going to need it to make the tail.

... continued from steps 13 to 24

25. To make the tail, fold down the center of the strip of paper to form a trough.

26. Tear as shown to form control surfaces. The folds should be parallel with the bottom of the trough.

27. Fold wings up.


28. Fold the right wing down as shown in photos 28 and 29. Take special care to angle this fold in such a way so that the leading edge of the wing is slightly higher than the trailing edge.

29. Study this photo and you will see that the fold is not exactly parallel with the trough at the bottom but slightly angled as described in photo 28.

30. The plane should look like this at this point.


31. Bend the wingtips up.

32. Insert tail into slot under wing.

33. Finished at last!


34. Aircraft shown with landing gears down. Note: the craft does not fly as well with the gears down.

35. Ready to fly! - IMPORTANT: For instructions on how to fly the model airplane, go to How to fly it.
发表于 2007-5-27 09:51:34 | 显示全部楼层
这个人是模型高手啊...........:L
回复

使用道具 举报

 楼主| 发表于 2007-5-27 11:36:43 | 显示全部楼层
转载的......
点how to fly
回复

使用道具 举报

发表于 2007-5-27 13:54:51 | 显示全部楼层
这个我小时候就会,只是没加上尾巴,哈~~
回复

使用道具 举报

发表于 2007-5-27 20:46:38 | 显示全部楼层
加了尾巴还能飞么?有同志试过了么?
回复

使用道具 举报

 楼主| 发表于 2007-5-29 18:49:54 | 显示全部楼层
http://www.guardian.co.uk/flash/0,5860,1648976,00.html
这个符合空气动力学原理,是leeds university研究出来的......叫做Avenger.
回复

使用道具 举报

您需要登录后才可以回帖 登录 | 注册

本版积分规则

关闭

站长推荐上一条 /1 下一条

Archiver|手机版|小黑屋|DeepTimes.NET 太空游戏站